Brooder Arduino - Revision history

TheInventurers at 17:27, 21 March 2017

2017-03-21T17:27:58Z

2017-03-16T18:19:15Z

‎Coding

2017-03-16T18:17:28Z

‎Coding

2017-03-16T18:17:02Z

‎Coding

2017-03-16T18:16:33Z

‎Coding

2017-03-16T18:16:01Z

‎Coding

2017-03-16T18:15:47Z

‎Coding

2017-03-16T18:14:49Z

‎Coding

2017-03-16T18:12:05Z

2017-03-16T18:08:06Z

Created page with "Insert Coding Here"

New page

Insert Coding Here

← Older revision		Revision as of 17:27, 21 March 2017
Line 1:		Line 1:
−	~~==Coding==~~
	*Note: this is code for connecting to a Dallas Temperature Sensor. By default, temperature is measured in Celsius.		*Note: this is code for connecting to a Dallas Temperature Sensor. By default, temperature is measured in Celsius.

@@ Line 1: / Line 1: @@
 ==Coding==
 <pre>
 #include <OneWire.h>

@@ Line 36: / Line 36: @@
 	Serial.print(sensors.getTempCByIndex(0)); // Why "byIndex"? // You can have more than one IC on the same bus. // 0 refers to the first IC on the wire
-	if (sensors.getTempCByIndex(0)>25.5 && sensors.getTempCByIndex(0)<27)
+	if (sensors.getTempCByIndex(0)>25.5 && sensors.getTempCByIndex(0)<27) //ADJUST TEMPERATURE PARAMETERS HERE
+	{
 		digitalWrite(11,HIGH);

@@ Line 1: / Line 1: @@
 ==Coding==
 <pre>
 #include <OneWire.h>
 #include <DallasTemperature.h>

@@ Line 1: / Line 1: @@
 ==Coding==
-<source lang="c++">
+<pre>
 #include <OneWire.h>
 #include <DallasTemperature.h>
@@ Line 46: / Line 47: @@
+}
-</source>
+</pre>

← Older revision		Revision as of 18:12, 16 March 2017
Line 1:		Line 1:
−	~~Insert~~ Coding ~~Here~~	+	==Coding==
		+	#include <OneWire.h>
		+	#include <DallasTemperature.h>
		+
		+	// Data wire is plugged into pin 2 on the Arduino
		+	#define ONE_WIRE_BUS 2
		+
		+	// Setup a oneWire instance to communicate with any OneWire devices // (not just Maxim/Dallas temperature ICs)
		+	OneWire oneWire(ONE_WIRE_BUS);
		+
		+	// Pass our oneWire reference to Dallas Temperature.
		+	DallasTemperature sensors(&oneWire);
		+
		+	void setup(void)
		+	{
		+	// start serial port
		+	Serial.begin(9600);
		+	Serial.println("Dallas Temperature IC Control Library Demo");
		+
		+	// Start up the library
		+	sensors.begin();
		+	pinMode(11,OUTPUT);
		+	}
		+
		+
		+	void loop(void)
		+	{
		+	// call sensors.requestTemperatures() to issue a global temperature
		+	// request to all devices on the bus
		+	Serial.print(" Requesting temperatures...");
		+	sensors.requestTemperatures(); // Send the command to get temperatures
		+	Serial.println("DONE");
		+
		+	Serial.print("Temperature for Device 1 is: ");
		+	Serial.print(sensors.getTempCByIndex(0)); // Why "byIndex"? // You can have more than one IC on the same bus. // 0 refers to the first IC on the wire
		+
		+	if (sensors.getTempCByIndex(0)>25.5 && sensors.getTempCByIndex(0)<27)
		+	{
		+	digitalWrite(11,HIGH);
		+	}
		+	else{
		+	digitalWrite(11,LOW);
		+	}
		+
		+	}